Content View Hits : 24078
Galvanized Hardware
Inside Corner |
 |
 |
| (WH-IC) The inside corner, working opposite the outside corner, sandwiches the wood, keeping bolts from burying themselves in the wood. This corner gusset will give the dock a lot of strength and stability. |
Outside Corner End |
 |
 |
| (WH-OCE) The outside corner end is used at the ends of dock, ends of fingers, or corners of swim platforms. |
|
|
Angle |
 |
 |
| (WH-A) Angles are used with a Washer Plate (WH-W) to hold cross stringers to side stringers. These two pieces of steel sandwich the wood, creating a solid corner. |
Washer Plate |
 |
 |
| (WH-W) The washer plate is used primarily with Angles (WH-A) and Cleat Angles (WH-CA). The plate has two square holes to keep the carriage bolts from turning when tightening them. |
Backup Plate |
 |
 |
|
(WH-B) Use the Backup Plate with our Single "T" Males (WH-SM) and Single "T" Females (WH-SF) for additional strength. They also keep the bolts from pulling through your wood. |
Single "T" Male |
 |
 |
| (WH-SM) The Single "T" Male has one 5/8" tab with a hole for a 3/4" Connector Pin (B-PIN) and is used with a Single "T" Female (WH-SF) or Outside Corner Female (WH-OCF). The male and female singles can both be used to make finger attachments by bolting them to the side of a dock. They can also be used to make ramps by bolting them to seawalls. |
Single "T" Female |
 |
 |
| (WH-SF) The Single "T" Female has two 1/2" tabs with holes for a 3/4" Connector Pin (B-PIN) and is used with a Single "T" Male (WH-SM) or Outside Corner Male (WH-OCM). The male and female singles can both be used to make finger attachments by bolting them to the side of a dock. They can also be used to make ramps by bolting them to seawalls. |
Outside Corner Male |
 |
 |
| (WH-OCM) The Outside Corner Male has one 5/8" tab with a hole for a 3/4" Connector Pin (B-PIN). Use with an Outside Corner Female (WH-OCF) or with a Single "T" Female (WH-SF) at the corner of your dock to attach a finger or dock section. |
Outside Corner Female |
 |
 |
| (WH-OCF) The Outside Corner Female has two 1/2" tabs with holes for a 3/4" Connector Pin (B-PIN). Use with an Outside Corner Male (WH-OCF) or with a Single "T" Male (WH-SF) at the corner of your dock to attach a finger or dock section. |
Cleat Angle |
 |
 |
| (WH-CA) The cleat angle has slots that accommodate various cleat sizes. Bolt the cleat angle to the side stringer using a Washer Plate (WH-W). Then bolt the cleat through the deck into the cleat angle. This will ensure that the cleat will not pull out of the deck. |
Splice Plates |
 |
 |
| (WH-SP) Our Splice Plates were designed to join two timbers together. One is used on each side. The bolt holes are drilled so that an angle and 1/ 1/2" lumber can be added at the splice and end up at the end of the splice. Our Splice Plates are sold in pairs. |
Outside Corner Female/Female |
 |
 |
| (WH-OCFF) Made to add a finger on the corner, and saves using a H-SM or H-SF. |
Inside Corner - 3" I.D. Pipe Holder |
 |
 |
| (WH-ICP3) Use the Inside Corner - 3" I.D. Pipe Holder in place of a regular inside corner to accommodate a 2" I.D. pipe. The 3" Pipe Holder is welded in place. |
3" Pipe Holder |
 |
 |
| (WHP-3) Our 3" Pipe Holder bolts to a side stringer. Use a 2" standard pipe to anchor your dock in place. |
Chain Retainers |
 |
 |
| (WH-CRS) Our Chain Retainer bolts to the side of your dock and uses chain to hold the dock in place. You can use 5/16", 3/8" or 1/2"chain. Use either (2) WH-W or (1) B as back up plates. 5" L x 5" H. |
 |